Single conversion
6 ft converts to approximately 1.8288 m. This is the direct calculator result using the standard factor.
Common conversion calculator
Feet to Metres Converter
Convert feet to metres with the exact formula, clear rounding notes and practical examples for everyday use.
On this page
How to convert feet to metres
input × 0.3048
This is useful for height, room dimensions and product measurements copied from imperial specs.
Feet to metres is useful for heights, room dimensions, property listings, aviation references and imported plans. Decimal feet and feet-and-inches are different notations and must be handled separately.
Worked examples
Reverse check
If you convert 1.8288 m back, you get approximately 6 ft. A tiny difference can appear because the displayed number is rounded.
Six feet is 1.8288 m, so a person or doorway around 6 ft should be a little under 2 m.
Quick feet to metres reference values
The table applies the same feet to metres formula used by the calculator.
| Feet | Metres |
|---|---|
| 1 | 0.3048 |
| 3 | 0.9144 |
| 5 | 1.524 |
| 6 | 1.8288 |
| 10 | 3.048 |
| 20 | 6.096 |
| 100 | 30.48 |
Use the nearest row to test whether a metres result is in the right range. Do not copy a rounded table value when the original feet measurement is more precise or the decision is close to a practical threshold.
Practical feet to metres example
Consider translating a 6 ft clearance from an imported equipment sheet. Starting with 6 feet, the formula gives 1.8288 metres.
Rounding, accuracy and common mistakes
Two decimal metres is usually adequate for a room or height comparison. Keep millimetres when the value comes from a plan, equipment clearance or a measured installation.
Convert inches separately or combine the full measurement into decimal feet before applying 0.3048.
Precision example: 6 ft×0.3048=1.8288 m. Display 1.83 m for a broad height comparison; keep 1.8288 m in a subsequent calculation.
Printable chart and related converters
The chart gives fast anchors for common heights and room lengths. Enter the exact feet value when it contains inches or decimals.
Length Conversion Chart
Use this printable reference for common feet to metres values, then return to the calculator for a specific or decimal input.
Open printable chartFeet to Metres Converter FAQs
What is the formula for feet to metres?
metres = feet × 0.3048.
How should I round feet to metres?
Two decimal metres is usually adequate for a room or height comparison. Keep millimetres when the value comes from a plan, equipment clearance or a measured installation.
What should I check before using the converted metres value?
Property plans, access clearances and construction work should be checked against the original drawing and applicable tolerance, not a rounded web result.
How to use this result in real decisions
Feet to metres is useful for heights, room dimensions, property listings, aviation references and imported plans. Decimal feet and feet-and-inches are different notations and must be handled separately.
A clean workflow is to preserve the original feet figure, record the converted metres figure beside it and round only for the final use. Convert inches separately or combine the full measurement into decimal feet before applying 0.3048.
Common mistakes in feet to metres
- Entering 5 ft 10 in as 5.10 feet.
- Rounding metres before converting the remaining inches.
- Using a square-foot factor for a linear measurement.
- Assuming a property listing is measured to the same standard as a construction drawing.
The reverse check and feet to metres anchor example are included to expose these errors before the metres result is copied elsewhere.
Calculator result versus chart result
The chart gives fast anchors for common heights and room lengths. Enter the exact feet value when it contains inches or decimals.
The feet to metres chart and calculator should agree at shared anchor values. If they do not, check the unit convention and direction before changing the number.
Bottom line
Use this page for a transparent feet to metres calculation, keep the source and result together, and apply the original source’s accuracy and limits. Property plans, access clearances and construction work should be checked against the original drawing and applicable tolerance, not a rounded web result.
Reviewed for calculator quality: This unit conversion calculator was checked for input clarity, formula notes, rounding behaviour, examples, related links and general-information limitations. See the methodology notes and editorial review profile.