Single conversion
1.8 m converts to approximately 5.905512 ft. This is the direct calculator result using the standard factor.
Common conversion calculator
Metres to Feet Converter
Convert metres to feet with the exact formula, clear rounding notes and practical examples for everyday use.
On this page
How to convert metres to feet
input ÷ 0.3048
Metres to feet helps with overseas property descriptions, height comparisons, equipment specifications and plans that use imperial units. A decimal foot result is not automatically written as feet and inches.
One foot is exactly 0.3048 metres.
Worked examples
Reverse check
If you convert 5.905512 ft back, you get approximately 1.8 m. A tiny difference can appear because the displayed number is rounded.
One metre is about 3.28 ft, so 2 m is roughly 6.56 ft rather than 6 ft 56 in.
Quick metres to feet reference values
The table applies the same metres to feet formula used by the calculator.
| Metres | Feet |
|---|---|
| 1 | 3.2808 |
| 1.5 | 4.9213 |
| 2 | 6.5617 |
| 5 | 16.404 |
| 10 | 32.808 |
| 50 | 164.04 |
| 100 | 328.08 |
Use the nearest row to test whether a feet result is in the right range. Do not copy a rounded table value when the original metres measurement is more precise or the decision is close to a practical threshold.
Practical metres to feet example
Consider explaining a 2 m room dimension to someone using feet. Starting with 5 metres, the formula gives 16.404 feet.
Rounding, accuracy and common mistakes
Use one or two decimal feet for broad comparison. Convert the decimal remainder into inches when a person, room or product dimension must be communicated in conventional feet-and-inches notation.
Keep the metre value intact until the final step, especially when the source was measured to the nearest millimetre or centimetre.
Precision example: 1.8 m÷0.3048=5.9055…ft. The decimal part is 0.9055×12=10.87 in, not 0.9055 in.
Printable chart and related converters
Use the length chart for common metre values and the calculator when the input includes centimetres or the output must be more precise.
Length Conversion Chart
Use this printable reference for common metres to feet values, then return to the calculator for a specific or decimal input.
Open printable chartMetres to Feet Converter FAQs
What is the formula for metres to feet?
feet = metres ÷ 0.3048.
How should I round metres to feet?
Use one or two decimal feet for broad comparison. Convert the decimal remainder into inches when a person, room or product dimension must be communicated in conventional feet-and-inches notation.
What should I check before using the converted feet value?
For construction, accessibility or equipment clearance, convert the specified tolerance as well as the nominal dimension.
How to use this result in real decisions
Metres to feet helps with overseas property descriptions, height comparisons, equipment specifications and plans that use imperial units. A decimal foot result is not automatically written as feet and inches.
Use the result as a labelled pair rather than replacing the source number. That makes a reversed conversion or regional-unit mistake easier to catch. Keep the metre value intact until the final step, especially when the source was measured to the nearest millimetre or centimetre.
Common mistakes in metres to feet
- Reading 6.56 ft as 6 ft 56 in.
- Converting metres to square feet when the source is a length.
- Rounding a measured 1.995 m to 2 m before conversion.
- Using an approximate 3.3 factor for a specification that needs tighter accuracy.
The reverse check and metres to feet anchor example are included to expose these errors before the feet result is copied elsewhere.
Calculator result versus chart result
Use the length chart for common metre values and the calculator when the input includes centimetres or the output must be more precise.
Keep the original measurement even when the metres to feet chart is sufficient, so a later decision can be checked without reconstructing the conversion.
Bottom line
Use this page for a transparent metres to feet calculation, keep the source and result together, and apply the original source’s accuracy and limits. For construction, accessibility or equipment clearance, convert the specified tolerance as well as the nominal dimension.
Reviewed for calculator quality: This unit conversion calculator was checked for input clarity, formula notes, rounding behaviour, examples, related links and general-information limitations. See the methodology notes and editorial review profile.